Door with completed replacement Multipoint Lock

Replacing a Multipoint Lock System in a uPVC Door

Door with completed replacement Multipoint Lock

The deadlock in this uPVC door failed so it was time to replace it with a new one. For the most part their are a couple of variants for the dimensions of Euro Profile door mechanisms. The face plate can be 16mm or 20mm in width and the depth from the centre of the cylinder to the face plate can be 35mm or 45mm. This one was a 16mm face plate width and 35mm cylinder depth.

First unscrew the handles and take the bolt out of the face plate that keeps the Euro Cylinder in place.

Undo screws and remove Extension Bars and Lock Plate
Undo screws and remove Extension Bars and Lock Plate

Then using the key adjust the revolving cam inside the Euro Cylinder to be in the downward position and pull the Euro Cylinder out. This will be used in the replacement system.

Euro Cylinder being removed by turning the key to put the revolving cam in a downward position to enable it to be pulled out
Euro Cylinder being removed by turning the key to put the revolving cam in a downward position to enable it to be pulled out

Then remove the face plate. Some times there can be separate face plates for the hooks at the top and bottom and the latch and lock in the middle. The replacement for this system has separate plates so the latch and lock plate is offered up first. The existing housing in the uPVC door needs some adjustment so that is cut using a drill and multitool to fit the new latch and lock case.

Adjust Centre Latch and Deadlock Housing
Adjust Centre Latch and Deadlock Housing

Once the lock case fits into the door then pilot holes are drilled in the door in the positions where the screws will be fitted to secure the face plate. The screws are then put into the face plate and tightened up. At this point put the Euro Cylinder is put back into the lock case using the key to make sure the revolving cam is in the downward position and the bolt is screwed back in to secure the Euro Cylinder. Put the spindle back through the latch and place the handles back on the door and do up their retaining bolts. Make sure the latch and deadlock move freely when turning the handle.

Offer up the latch and lock plate keep to the frame and make sure the existing keep housing in the door frame is in the right position otherwise adjust as required. On this system there is a datum line on the face plate in the door that has to match up with a datum line on the keep. The keeps for this system have packing grub screws to allow a secure footing when the keep overlaps thinner keep gully’s of the old door frame but they are not long enough for these older frames so I used pieces of wood screwed into the metal part of the door frame by drilling pilot holes and securing the wood strips with self tapping screws. Then drill pilot holes for the keep screws and screw the keep to the frame. Test shutting and locking the door and adjust the keep plates as necessary with the grub screw adjusters.

Lock Keep fitted in position and being adjusted to accept Latch and Deadlock
Lock Keep fitted in position with packing and being adjusted to accept Latch and Deadlock

This system has a roller as well as a hook to pull the door tight when turning the handle but some just have a hook. Offer up the bottom hook and roller face plate and adjust the housing in the door by cutting the uPVC as necessary.

Adjust bottom housing for hook case
Adjust bottom housing for hook case

When offering up the hook plate make sure the hook is in the fully retracted position when you place the outer male toothed conrod of the hook face plate into the female toothed conrod of the centre lock plate.

Centre Lock Plate Conrod with Female Toothed Section
Centre Lock Plate Conrod with Female Toothed Section

The hook unit case is also sometimes called the gearbox. When you are happy that the hook plate is in the best position to work with the centre lock plate and the existing keep housing in the door frame make pilot holes where the fixing screws should go through the door and then insert the screws and do them up. This system has a cover plate which has a location pip which locates in the centre lock plate and then a grub screw into the hook plate to cover the join between the two.

Cover Plate for Centre Lock Plate and Hook Plate
Cover Plate for Centre Lock Plate and Hook Plate

Go through the same process for the bottom hook plate keep as was applied to the centre lock plate keep and test the mechanism. Pay special attention to the hooks and that they clear the bottom of the keep when closing. Repeat the process for the top lock plate keep.

Top Hook and Roller keep fitted to the frame with packing
Top Hook and Roller keep fitted to the frame with packing

Once all the keeps are fitted test closing, locking, un-locking and re-opening the door.

Door with completed replacement Multipoint Lock
Door with completed replacement Multipoint Lock

To have an article featured, email:
editorial@propertyauctionaction.co.uk

To advertise, contact:
advertising@propertyauctionaction.co.uk


You may also like these articles...

Slabs laid ready for grouting

Enhance your property by laying a new patio – part #5

With the ground levelled, falls going the right way around the property and the MoT type 1 spread over and compacted with a petrol plate the slab laying is now ...
Read More
Slate Tiles

Enhance your property by laying a new patio – part #4

With most of the below ground works finished it’s now time to start building the ground back up. A green led laser level (more easily seen in daylight) was used ...
Read More
New drainage pipe for channel drain

Enhance your property by laying a new patio – part #3

Round by the garage and the back door of the property the wall of the garage is built into the bank of the house next door. The gravel boards of ...
Read More
subbase collapse under patio

Enhance your property by laying a new patio – part #2

This is part 2 of the patio replacement project which we are starting for the summer. We have pulled up the old patio slabs revealing the thin sand base layer ...
Read More
Old uneven patio

Enhance your property by laying a new patio – part #1

Now that the summer is fast approaching it is time to start thinking about your outside spaces. This patio is twenty years old and is beginning to show its age ...
Read More
Repair broken roof tile and rotten fasci and box end

Roof Repair Case Study – Broken Roof Tile and Rotten Fascia

Roof Repair - Broken roof tile leading to a rotten fascia and box end One of the roof the tiles was cracked all the way down the centre of the ...
Read More

Renovate your favourite old chair

Do you have a favourite leather or vinyl sofa in your house or perhaps chairs at your office or in a salon that are beginning to show their age or ...
Read More
Finally The Engineered Oak Floor Is Complete

Make Your House Entrance Hall Pop With An Engineered Oak Wood Floor

The entrance hall is the first thing that everyone sees when they step into to your property. One of the easiest ways to give your house an upgraded hallway is ...
Read More
Loading...