A tired bathroom can bring down the whole tone of a property without even having to try too hard and yet by the same token just applying a little bit of elbow grease and some relatively inexpensive products and you can lift the ambiance to another level. If you have old-style patterns on your tiles then there are ways you can improve the look of them without having to got to all the trouble and expense of removing them.
Over time bathrooms take a bit of a battering. We take long hot showers and baths that submit the fabric of the room to heat and damp and invariably the amount of ventilation falls short of that which would be required to keep the walls mould free. Having the occurrence of mould is not ideal as at high enough concentrations it can be detrimental to health. Consider upgrading an existing extraction fan to a more powerful version if you are battling mould. There are number of different manufacturers who produce innovative designs which can help to remove steam from the room. Advances in technology mean that more power does not have to equal more noise as there are quiet versions available. Be careful to get the correct diameter aperture or be prepared to open up the existing hole in the ceiling to accept the new fan. Reducers can be used to connect the fan to the ducting if a step down in size is required. Also, there are versions that can be set to activate when a certain level of humidity is detected or with PIR sensors to activate when someone enters the room.
Now we need to set about getting rid of the mould from the surface of the tiles and the grout. By it’s nature mould can be very difficult to get rid of. For tile grout try rubbing the grout vigorously with a neat solution of bleach. If the grout is very ingrained then try leaving the bleach on the surface over night before rubbing again the next day. Strip out any caulking using a sharp knife and clean the joints out with more bleach. For the surface of the tiles try a solution of white wine vinegar and lemon and rub them vigorously with a scouring pad.
Once the tiles are all cleaned up then rub them down with some 180 grit sand paper. You don’t have be too fastidious when doing this but just enough to make sure all the tiles have been sanded to some extent. Wash the tiles off with some sugar soap. Now the tiles are ready to be painted. Tile paints come in a variety of colours. Try to pick a manufacturer that produces a low VOC paint that does not give off high levels of toxic vapours while you are applying it. Keep as many windows open as possible while painting and wear a mask. Use a roller to apply the paint to give a smooth finish. You will probably need at least two coats maybe three depending on what sort of colour and patterns you are attempting to cover. Leave the paint to dry for at least 24 hours and then use a fine tipped grout pen to put the grout lines back. Apply 2 coats to the grout lines especially inside shower cubicles. You will probably use a multiple number of grout pens depending on tile size and area to be covered. Leave the grout lines to dry for 24 hours and then seal them in the wet areas with a clear grout sealer solution.
Make sure you get any mould off the ceiling by scrubbing well with an anti mould solution and allow to dry for a few hours. Then re-paint with an anti mould and a stain blocking paint. You will probably need to apply at least two coats and maybe three in problem areas.
Now you have your bright new painted tiles you want to make sure the rest pf the bathroom looks gleaming too. Shower screens in hard water areas usually become ingrained with mineral deposits like limescale that are really tough to get off. Try soaking the glass in a solution of white wine vinegar and lemon mixed with water. Be liberal with the white wine vinegar. Wear gloves and scrub well with a non scratch scouring sponge. This process will have to be repeated several times in order to achieve a gleaming finish. If the residue proves to be really tough then there are some chemical cleaners on the market that can tackle really bad limescale deposits but be careful when handling these and wear gloves, a mask and eye protection. If all else fails then you can sometimes source replacement parts for shower enclosures. Curved doors for quadrant shower enclosures can sometimes be interchanged but make sure the door height is correct and the side lengths match. Common heights are 1850mm, 1900mm, and 2000m with some common side depth sizes being 800mm, 900mm or 1000mm. You can also buy replacement shower door rollers. These usually become frozen up over time with limescale that stops the dolly wheels from turning. Some have needle roller bearings which seize up as well. You can replace a single wheel with a double wheel as long as the fixing holes that go through the glass are the right size and placement. Make sure the dolly wheel is the correct size for the track as well usually 20mm or 25mm diameter but other sizes are used as well. Normally the top set of wheels are fixed and the bottom set are spring loaded to allow the doors to be removed and replaced easily in the tracks.
The other area of the shower that discolours over time is the plastic seals on the doors and side glass. This can be purchased separately. Make sure you get the right profile for the seal being replaced and enough length to replace all the seals. Re-do any mastic seal caulking that has been removed and replace with an anti-mould caulk. Sometimes it can be useful to mask either side of the caulk line and use a smoothing tool to get a good finish. Remove the masking tape before the caulk has set.
Some of the the last areas to address are missing cover caps on screw fixings and making sure all chrome surfaces are limescale free and gleaming. Now you have achieved a bright and fresh bathroom on a relatively small budget.
You can also read – WHY CHOOSE DIY FURNITURE?